催燃燒運行狀態燃空比的調定，催化燃燒時的空氣比值范圍一般在4%-11%之間。在燃燒條件之下，能實現較好的催化燃燒效果，燃燒系統就可以得到熱效率，同時又能取得較好的排放效果。

The adjustment of the fuel air ratio during catalytic combustion operation generally ranges from 4% to 11%. Under combustion conditions, good catalytic combustion effects can be achieved, and the combustion system can achieve thermal efficiency while also achieving good emission effects.

燃燒起動過程通過紫外線傳感器的檢測到期小火點燃后，打開主燃氣閥門。這時爐盤進行有焰燃燒，直到檢測溫度信號達到設定的點火關閉溫度，點火閥門關閉，完成點火過程，進入到燃燒調節階段。

The combustion start-up process is detected by the ultraviolet sensor, and after the small flame is ignited, the main gas valve is opened. At this point, the furnace plate undergoes flame combustion until the temperature signal reaches the set ignition off temperature, the ignition valve closes, and the ignition process is completed, entering the combustion adjustment stage.

當控制系統在待命的狀態下，接到輸入的起動命令，將進入燃燒運行狀態，先是控制系統進行自檢，之后進行前吹掃，變頻器輸出信號控制風機的旋轉，空氣風量由低速漸變?yōu)楦咚僭僦饾u變?yōu)榈退伲迈r空氣風吹過燃燒爐盤，以保證爐內沒有殘留燃氣的存在，保證點火過程的可靠。

When the control system is in a standby state and receives an input start command, it will enter the combustion operation state. First, the control system performs self check, and then performs front blowing. The frequency converter outputs a signal to control the rotation of the fan, and the air volume gradually changes from low speed to high speed and then to low speed. Fresh air is blown through the combustion furnace to ensure that there is no residual gas in the furnace and the ignition process is reliable.

可根據需要分別設定點火溫度和變頻器起動時的頻率，控制風機的風量。點火溫度是為了保證點火過程的可靠性。起動頻率保證催化燃燒器在剛點燃時的有焰燃燒，這時的燃燒比不易太低，風量不能過大。

The ignition temperature and frequency at which the frequency converter starts can be set as needed to control the airflow of the fan. The ignition temperature is to ensure the reliability of the ignition process. The starting frequency ensures that the catalytic burner burns with flames when just ignited, and the combustion ratio at this time is not too low, and the air volume cannot be too large.

催化劑的加入并不能改變原有的化學平衡，所改變的僅是化學反應的速度，而在反應前后，催化劑本身的性質并不發生變化。催化燃燒設備主要由活性炭吸附箱、阻火器、熱交換器，催化反應床，風機等主要部件組成。對催化燃燒設備選型要根據自身的需求來進行。

The addition of catalysts does not alter the original chemical equilibrium, only the rate of chemical reaction, and the properties of the catalyst itself do not change before and after the reaction. The catalytic combustion equipment mainly consists of active carbon adsorption box, flame arrester, heat exchanger, catalytic reaction bed, fan and other main components. The selection of catalytic combustion equipment should be based on one's own needs.

更多的關于催化燃燒設備問題或者詳細的內容，請進入我們公司的網站：http://www.7895392.cn網站中會有很多的內容僅供參考

For more information or detailed information about catalytic combustion equipment, please visit our company's website: http://www.7895392.cn There will be a lot of content on the website for reference only